Exactly How to Replace a Tub Yourself: Removing and Replacing.
Exactly How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
Do you find yourself searching for information and facts on Installing A Bathtub?
Installing a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and also in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the brand-new one. Ensure you have qualified on your own for the work as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is far better to think about using one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This article will assist you mount a new bath tub in your restroom if you have actually already gotten a brand-new bathtub and also do not require to alter the arrangement of your previous water system pipelines.
Your devices and also material checklist need to consist of the following:
Preparing for the Setup
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome as a result of the restricted access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the needed position. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub till the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as also check the overflow outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall surface between the bath and also the tiling, leading to problems with moisture as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked paper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealant can split fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is advisable to fit the tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our section about How to Install a Bathtub. Thanks a lot for finding the time to browse our piece. Feel free to set aside a second to promote this page if you liked it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Request An Estimate Report this page